#Hardware moca cable disconnected fios full#
#Hardware moca cable disconnected fios software#
#Hardware moca cable disconnected fios mac#

I just use a different native VLAN to connect to the ONT as the other ports with inside devices on them and then just tag all the VLAN through the single “FIOS pulled” Ethernet cable. The advantage here is that I have Ethernet devices near my ONT in the garage that need connectivity (cameras etc) and I don’t want to have to run another Ethernet cable.

I have an additional advantage for the switch in the middle actually I put a switch at the ONT end and the other end of the connecting Ethernet cable connects to my home’s core switch. In this configuration it is critically important to make sure that there is no intra-VLAN traffic, as that could allow an attacker to bypass your firewall! These need to be untagged, completely segregated VLANs.

#Hardware moca cable disconnected fios mac#

Your ISP (Frontier FioS in my case) would not be aware that there is more than one router connected, because the devices share a virtual MAC address and the IP address that your ISP handed you via DHCP. This would allow for failover in the case of a router failure. If you have two routers in a CARP (failover) configuration you’d just add a 3rd port to this VLAN and connect both routers. This gives you the option to mirror either port to a third port on the switch allowing you to sniff traffic outside the firewall. Plug the ONT into one port and the WAN interface of the router into the other port. This option creates a Virtual LAN on two ports on a managed switch. Option 2 is the better, more robust solution, but it does require a VLAN capable switch and a little understanding of more complex networking scenarios. These desktop class switches are also made with cheaper components which might impact performance, and they are more prone to failure.įigure 1: Desktop Switch between the ONT and the Router Option 2: Use a WAN VLAN between the ONT and the router However, it will not give you the ability to mirror a port for traffic sniffing.

#Hardware moca cable disconnected fios software#

For some hardware or software incompatibilities where you just don’t want the router to be aware the WAN link is down physically (such as the router is on UPS and the ONT is not. This will give you the ability to keep the WAN link on your router up and all times, even if the ONT fails. The obvious choice might be just to place a desktop switch between the ONT and the router. Option 1: Place a desktop switch between the ONT and the router You may think your ISP is at fault only to learn your proxy server (think Squid) is acting up. It’s also a great way to make sure your firewall or internal network is operating correctly. This can be an incredibly effective way of seeing just what data is passing between the ISP and your network. The great thing about having a switch between the ONT and the router is that it make it incredibly easy to mirror the ONT’s port and put a sniffer such as WireShark on the line to listen to packets in the wild. Sometimes there are hardware or software problems with your router that can be mitigated by putting a device between them (such as the one where pfSense won’t reestablish WAN link after it fails). Sometimes you need to prove to yourself that the issue on your end. Sometimes you need to be able to prove to your ISP that the issue is on their end. So what does all of this have to do with putting a switch between the ONT and the router? Putting a Switch between the FiOS ONT and Router The ping times are up, the jitter is up, and pretty much everything about the FiOS service that was great was now gone, with the exception of shear throughput.

Then Frontier communications bought the Texas area, what was once glorious internet became average internet.

#Hardware moca cable disconnected fios full#

You could even get full gigabit speeds in some areas. Even Charter and Time Warner cable were only offering 2 or 3 megabits in the areas where they were actually available. FiOS came along rocking 15Mb/s down and 5Mb/s up. The fastest stuff on the block was DSL from Verizon or AT&T at 1.5Mb/s down and 128 Kb/s up and it wasn’t reliable at all. The city I live in (Keller, TX) was the first city in the nation to get FiOS! It was fantastic. When FiOS was first launched by Verizon it was a glorious time.